The front, center, and rear hanger brackets for the Dexter Tandem-Axle Trailer Hanger Kit for 3" Slipper Springs - 48-1/2" Axle Spacing Item # HAP-103-203-03 are as follows:
6-1/4" Tall front hangers with 1" bolt holes
4-1/8" Tall center hangers with 1-1/8 bolt holes
7-11/16" Tall rear hangers with 1/2" bolt holes view full answer...
I had the base of the Grommet for Peterson 850 Series Trailer Lights # PE26WR measured and it will be 5-1/2" x 3-5/8". With that said, I would go a hair under these measurements to make sure it is a good, snug fit. view full answer...
I have included a picture with the vertical distances for you to see. The overall height of the Pack'em Trimmer Rack # PK-6 is 46". It is capable of holding 3 trimmers with a trimmer pole that is 1-5/8" in diameter or smaller.
The distance on the fixed bracket arm is 9" from the trimmer pad to the bottom of the next bracket. On the locking side the distance is 8-1/8" due to the thickness of the hinge arm. view full answer...
In order to properly weigh your door to figure out the correct spring you only need to find the weight when the ramp door is down. You do not need to remove the door to find this weight.
You will need a scale in order to measure the weight, a bathroom scale will do. Place a block of wood or other durable material on the scale and rest the end of your ramp on the block. This will give you the weight of your door. Don't forget to subtract out the weight of the block for a more accurate... view full answer...
The # e98840 etrailer Trailer Hitch Receiver has a maximum gross towing weight of 6,000 lbs and tongue weight of 900 lbs. As long as the boat you are towing does not exceed these weights the hitch will not have any issues. If you are towing a larger boat, it is possible to increase the gross towing weight to 8,000 lbs by using weight distribution. I also recommend checking your vehicle owner's manual for its specific capacities. You will need to follow whichever capacity is lower, the hitch... view full answer...
As far as crossbar width, there is no set maximum that is set by manufacturers. It truly depends on the models of crossbars they offer for your 2019 Subaru Forester. Accessories that you mount on your crossbars will have different compatibilities based on the width of the crossbars you choose. If you have an accessory in mind, I would be happy to assist with crossbar compatibility.
If you are curious about crossbar length, our fitguide provides compatible lengths of crossbars for your... view full answer...
While two Thule Hullavators will fit the dimensions of your 68-inch wide crossbars and are compatible with the t-channels on the Yakima HD bars on the Yakima Overhaul HD # Y01151-5868, one of the things to note is that the Hullavator requires 4-8 inches of crossbar space after the leg supports of the OverHaul HD in order to function properly. Since every ladder rack fits every truck model differently, I recommend measuring your crossbars outisde of your truck's bed rails to see if there... view full answer...
The Valterra Folding Manual Stabilizer for Trailers and RVs # 020106 only comes with the 27" legs and 14" to 28" clearance range. Since the stabilizers are only intended to help reduce bouncing and swaying in your parked camper, placing blocks underneath them should not pose a problem.
I recommend using leveling blocks like the Ultra-Fab Leveling Blocks for Trailers and RVs - 8-1/4" Wide x 8-1/4" Long - Qty 4 # UF48-979050. These blocks are stackable which will allow you to adjust to... view full answer...
The distance from the center of the axle to the trailer frame of the Timbren part # TSR7000T05 of 6-3/8 inches is without a load on the suspension. This is also where the suspension would sit without an excessive load on the trailer as well. view full answer...
The 5" monitor included with the Furrion Vision S Wireless RV Observation Camera System w/ Side Marker Light Cameras - 5" Screen # FCE48TASL-05 you were looking at uses a .85" diameter ball for mounting.
If your existing mounts are not .85" you can use the included suction cup mount.
I included a video of the Furrion Vision S # FCE48TASL-05 for you to take a look at. view full answer...
The combined weight of both pieces of the BedRug Custom Truck Bed Mat - Bed Floor Cover for Trucks with Bare Beds or Spray-In Liners # BMH17RBS is about 8 pounds. With this information, one of the things you can do is find something that weighs 8 pounds (with using a scale) and place it on your 2020 Honda Ridgeline's trunk to test it. view full answer...
The different weight capacity of the SumoSprings Rebel Custom Helper Springs # SSR-327-40-2 (2600 pounds) and the # SSR-327-47-2 (4600 pounds) describes how much resistance the springs have. The # SSR-327-2 (2600 pounds) will have less spring resistance given to your frame than the # SSR-327-47-2 (4600 pounds). Given the weight of your 2020 Mercedes-Benz Sprinter 2500 (around 9,000 pounds), I recommend the # SSR-327-47-2 because it will be more effective at giving the support you need on... view full answer...
The hinge that allows the Thule EasyFold XT Bike Rack for 2 Electric Bikes # TH903202 to fold is not lockable. It's not a common issue that a thief or troublemaker would tilt bike racks to cause damage so it's not a feature our bike rack manufacturers make lockable. view full answer...
The part # C17125 is actually for a weight distribution system so if you were looking for an adjustable ball mount that has a 2 inch ball with more drop we do have the part # HD2014 which can do 14 inches of rise or drop. view full answer...